DID614

DID614/593×593/LE

Tapered hole pattern

Adjustable twin nozzles

Water connections

Fixing brackets

Geprüft nach VDI 6022

DID614

Four-way active chilled beam for ceiling grid, dimensions 600 × 600 mm and 625 × 625 mm, with horizontal heat exchanger

Active chilled beam for heating and cooling, with 2-pipe or 4-pipe heat exchanger, for integration with various ceiling systems.

Preferably for room heights up to 4.00 m
High heating and cooling capacity with a low conditioned primary air volume flow and low sound power level
High comfort levels due to low airflow velocity in the occupied zone
5 nozzle variants for demand-dependent induction: 4 nozzles each with different opening diameters, 1 twin nozzle with adjustable opening diameters
Removable induced air grille, no tool required
Induced air grille with tapered hole pattern

Optional equipment and accessories

Control system
Adjustable air control blades for air direction control
Different looks due to powder-coated surfaces
With an extended border also suitable for freely suspended installation

General information

Application

Active chilled beams of Type DID614 for the integration into various ceiling systems, preferably for room heights up to 4.00 m
Particularly suitable for grid ceilings with grid size 600 or 625
Adjustable air control blades (optional) allow for the manual adjustment of the four-way air discharge
Large volume flow rate range due to the adjustable twin nozzles (optional)
2-pipe or 4-pipe heat exchangers enable good comfort levels with a low conditioned primary air volume flow rate
Energy-efficient solution since water is used for heating and cooling

Special characteristics

Four-way air discharge
Horizontal heat exchanger as 2-pipe or 4-pipe system
Induced air grille with parallel drilled apertures, decreasing towards the edges
Optional twin nozzles, adjustable, for a large volume flow rate range
Water connection, Ø12 mm Cu pipe or coupling with G1/2" external thread and flat seal or G1/2" union nut and flat seal
Internal nozzle plate with punched nozzles (noncombustible)
Adjustable air control blades for air direction control as an option

Nominal sizes

600, 1200 mm

Variants

Heat exchanger
2: 2-pipe systems
4: 4-pipe systems

Nozzle variants

HE: Small
S1: Medium
S2: Large
HP: Extra large
DA: Adjustable twin nozzles, all nozzles are open (factory setting)
DS: Adjustable twin nozzles, smaller nozzles are open
DB: Adjustable twin nozzles, large nozzles are open. DS and DB can be set according to local requirements. You should order DA and have DS or DB set by others.

Construction

Powder-coated RAL 9010, pure white, gloss level 50 %
P1: Powder-coated in any other RAL colour, gloss level 70 %
P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Attachments

Adjustable air control blades
Water connection A1: G˝" external thread and flat seal
Water connection A2: G˝" union nut and flat seal

Useful additions

Connecting hoses
Control equipment consisting of a control panel including a controller with integral room temperature sensor; valves and valve actuators; and lockshields
X-AIRCONTROL control system

Construction features

Spigot is suitable for circular ducts to EN 1506 or EN 13180
4 fixing brackets for customer-side mounting
5 nozzle variants for demand-dependent induction: 4 nozzles each with different opening diameters, 1 twin nozzle with adjustable opening diameters
Internal nozzle plate with punched nozzles (noncombustible)
Removable induced air grille, fixed with magnets
Securing the induced air grille with safety cables

Material and surfaces

Casing, spigot, and perforated induced air grille made of galvanised sheet steel
Heat exchanger with copper tubes and aluminium fins
Exposed surfaces are powder-coated, pure white (RAL 9010), or in any other RAL colour
Air control blades made of polypropylene, UL 94, flame retardant (V0)
Steel nozzle plate

Standards and guidelines

Products are certified by Eurovent (no. 09.12.432) and listed on the Eurovent website
Declaration of hygiene conformity to VDI 6022

Maintenance

No moving parts, hence low maintenance
The heat exchanger can be vacuumed with an industrial vacuum cleaner, if necessary
VDI 6022, Part 1, applies (Hygiene requirements for ventilation and air-conditioning systems and units)

Technické údaje

Schematic illustration of DID614

1 Fixing brackets

2 Primary air spigot

3 Casing

4 Nozzle plate with punched nozzles

5 Air control blades (optional)

6 Water connections

7 Encasing

8 Heat exchanger

9 Front frame

10 Induced air grille

Functional description

Active chilled beams provide centrally conditioned primary air (outdoor air) to the room and use heat exchangers for additional cooling and/or heating. The primary air flows through the nozzles into the mixing chambers. This induces secondary air. The secondary air flows through the induction grille and the horizontal heat exchanger. There it is heated or cooled. Primary and secondary air mix and are then supplied to the room horizontally through the supply air slots.

Active chilled beams, with four-way air discharge and high thermal output, for air-water systems. For installation flush with the ceiling, preferably in rooms with a height up to 4.00 m. The units consist of a casing with mounting brackets, primary air plenum, non-combustible nozzles, and horizontal heat exchanger. 5 nozzle variants for demand-dependent induction: 4 nozzles each with different opening diameters, 1 twin nozzle with adjustable opening diameters.

Special characteristics

Four-way air discharge
Horizontal heat exchanger as 2-pipe or 4-pipe system
Induced air grille with parallel drilled apertures, decreasing towards the edges
Optional twin nozzles, adjustable, for a large volume flow rate range
Water connection, Ø12 mm Cu pipe or coupling with G1/2" external thread and flat seal or G1/2" union nut and flat seal
Internal nozzle plate with punched nozzles (noncombustible)
Adjustable air control blades for air direction control as an option

Material and surfaces

Casing, spigot, and perforated induced air grille made of galvanised sheet steel
Heat exchanger with copper tubes and aluminium fins
Exposed surfaces are powder-coated, pure white (RAL 9010), or in any other RAL colour
Air control blades made of polypropylene, UL 94, flame retardant (V0)
Steel nozzle plate

Construction

Powder-coated RAL 9010, pure white, gloss level 50 %
P1: Powder-coated in any other RAL colour, gloss level 70 %
P1: Powder-coated RAL 9006, white aluminium, gloss level 30 %

Technical data

Nominal length: 600, 1200 mm
Length: 593, 598, 618, 623 mm (one tile), or 1193, 1198, 1243, 1248 mm (two tiles)
Height: 230/245 mm
Width: 593, 598, 618, 623 mm
Primary air spigot, diameter: 123/158 mm
Primary air volume flow rate: 14 – 87 l/s or 50 – 310 m³ /h
Cooling capacity: up to 2170 W
Heating capacity: up to 2990 W
Max. operating pressure: 6 bar
Max. operating temperature: 75 °C

Sizing data

Primary air

qv [m3/h]
Δpt [Pa]

Air-regenerated noise

LWA [dB(A)]

Cooling

Qtot [W]

Heating

Qtot [W]

DID614

–

593 × 593

–

123

P1 - RAL 9016

1 Type
DID614 Active chilled beam

2 Design variant
No entry: perforated front plate, with decreasing apertures towards the edges

3 Heat exchanger
2 2-pipe
4 4-pipe

4 Nozzle variants
HE small
S1 Standard, small
S2 Standard, large
HP extra large
DA Twin nozzles (factory setting - all nozzles are open)

5 Position of water connection
R right
L links

6 Water connection (without control package)
No entry: plain copper tube Ø 12 mm
A1 with G½" external thread, flat seal
A2 with G½" union nut, flat seal

7 Overall dimensions [mm]
Length × width
593 × 593 (nominal size 600 × 600)
598 × 598 (nominal size 600 × 600)
618 × 618 (nominal size 625 × 625)
623 × 623 (nominal size 625 × 625)
1193 × 593 (nominal size 1200 × 600)
1198 × 598 (nominal size 1200 × 600)
1243 × 618 (nominal size 1250 × 625)
1248 × 623 (nominal size 1250 × 625)

8 Primary air socket diameter ØD [mm]
123, 158, 198

9 Exposed surface
No entry: powder-coated, RAL 9010 (pure white)
P1 powder-coated, specify RAL CLASSIC colour

Gloss level
RAL 9010 GU 50
RAL 9006 GU 30
All other RAL colours GU 70

10 Adjustable air control blades
No entry: without air control blades
LE with air control blades

Order example: DID614-4-S1-R-A2/593×593-123/P1-RAL9016/LE

Type	DID614 – Active chilled beam
Design variant	Round perforated metal plate, encased
Heat exchanger	4-pipe
Nozzle variant	Standard, small
Position of water connection	right
Water connection	with G½" union nut, flat seal
Overall dimensions [mm]	Length 593, width 593
Primary air spigot diameter [mm]	123
Exposed surface	powder-coated, RAL 9016 (traffic white)
Air control blades	with air control blades

Stažení

informace o produktu

Product Data Sheet Type DID614

DID614_PD_2025_04_29_DE_en Product Data Sheet 740 KB pdf

certifikáty

Declaration of hygiene conformity Type DID614

DDID614_HC_2024_05_DE_en Hygiene certificate 1,7 MB pdf
Eurovent Certita Certification Active and Passive Chilled Beams

Active-and-Passive-Chilled-Beams_CE_EUROVENT_09.12.432_2023_09_DE_en_fr Certificate 200 KB pdf
Non-CE Manufacturer's statement DID614

DID614_NotCE_2022_02_08_14_12_24_DE_en Certificate 1,7 MB pdf

návody k obsluze

Installation manual Type DID614

DID614_IM_CD10077_V1_2024_04_GB_en Installation manual 1,3 MB pdf

Kliknutím na tlačítko nám umožníte, abychom Vám poskytli vynikající zážitek z webových stránek a snadné nákupní procesy. Tyto soubory cookie zahrnují ty, které jsou nezbytné pro provoz stránek a pro kontrolu našich služeb a aplikací, stejně jako ty, které se používají pouze pro statistické účely, pro pohodlné nastavení nebo pro zobrazení personalizovaného obsahu. Můžete se rozhodnout, které kategorie chcete povolit, a můžete upravit nastavení využití dat podle svých individuálních požadavků. Upozorňujeme, že v závislosti na nastavení, které jste vybrali, nemusí být všechny funkce stránky k dispozici. Svůj výběr můžete kdykoli změnit.

TECHNICKY NEZBYTNÉ

Tyto cookies jsou nezbytné pro správné fungování našeho webu a nelze je deaktivovat. Tyto soubory cookie se zpravidla nastavují pouze v reakci na Vámi provedené akce, například nastavení vašich předvoleb ochrany osobních údajů nebo naplnění nákupního košíku. Kromě toho jsou integrovány funkce nebo podpora související se zabezpečením prostřednictvím specializovaného webchatu, včetně všech cookies relací od TROX nastavených po přihlášení jako zákazník. Můžete nastavit svůj prohlížeč, blokovat tyto soubory cookie nebo o nich informovat. Výsledkem je, že některé oblasti webu nemusí fungovat tak, jak bylo zamýšleno.

DID614

Four-way active chilled beam for ceiling grid, dimensions 600 × 600 mm and 625 × 625 mm, with horizontal heat exchanger

General information

Technické údaje

Stažení

informace o produktu

Product Data Sheet Type DID614

certifikáty

Declaration of hygiene conformity Type DID614

Eurovent Certita Certification Active and Passive Chilled Beams

Non-CE Manufacturer's statement DID614

návody k obsluze

Installation manual Type DID614

TROX Services

TECHNICKY NEZBYTNÉ

STATISTIKA A ANALÝZA WEBOVÝCH STRÁNEK

POHODLÍ A PERSONALIZACE

PRO NEJLEPŠÍ ZÁŽITEK S TROX